HP HPE6-A85 Actual Free Exam Questions & Community Discussion

Exam Code/Number: HPE6-A85
Exam Name/Title: Aruba Campus Access Associate Exam
Certification Provider: HP
Corresponding Certification: ACA Campus Access Associate

Exam Questions: 104
Updated On: May 30, 2026

Question #29

What does a wireless client do first when its countdown timer reaches zero and it receives a Transmit Opportunity (TXOP)?

A. It sends a reassociation request frame to the AP and sends its Data Frames.

B. It immediately sends its Data Frames and receives an ACK from the AP.

C. It sends a CTS-to-self announcement to the AP and all other clients.

D. It sends a CTS-to-self announcement to the ESP gateway.

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #30

You have physical access to an Aruba CX-Switch with unknown/lost credentials. What are the possible steps to rebuild the credentials? (Select two.)

A. Connect the switch via the console. Then, power cycle the switch.

B. Use boot profile 0.

C. Press and hold the clear button. Then, power-cycle the switch.

D. Press and hold the clear button. Then, press the reset button for 2 seconds and release both buttons.

E. Call Aruba support for a one-time password.

Discussion 0

Correct Answer: B,C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #31

A network technician is verifying that a customer successfully connected to the guest network after completing the captive portal. The network technician looks at the access tracker in ClearPass.
Which role should be seen when looking at the OUTPUT tab for the customer's session?

A. Guest authenticated

B. Guest logon

C. Captive portal login

D. Captive portal redirect

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #32

A network technician at a branch office is connecting VolP phones to a newly configured AOS-CX switch.
Users are complaining that voice quality is not as good as at the corporate office. Further investigation shows the local-priority value at the branch office is 1 while at the corporate office is 5.
What describes the issue regarding the default QoS behavior on the AOS-CX switch?

A. The QoS trust is set to CoS by default, and the VolP phone's local-priority value is mapped to 1.

B. The QoS trust is set to none by default, and each VolP phone's local priority is configured for CoS map entry 0.

C. The QoS trust is set to DSCP by default, and the VolP phone's local-priority value is mapped to 1.

D. The QoS trust is set to none by default, and each VolP phone's local priority is configured for CoS map entry 1.

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #33

Refer to Exhibit.
Which server will receive the smallest quantity of data?

A. 10.99.26.25

B. 10.100.100.25

C. 192.168.0.56

D. 172.17.17.43

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #34

Review the configuration below.
Why would you configure OSPF to use the IP address 10.1.200.1 as the router ID?

A. The IP address associated with the loopback interface is routable and prevents loops

B. The loopback interface state is dependent on the management interface state and reduces routing updates.

C. The loopback interface state Is independent of any physical interface and reduces routing updates.

D. The IP address associated with the loopback interface is non-routable and prevents loops

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #35

You are in a meeting with a customer where you are asked to explain the network redundancy feature Multiple Spanning Tree (MSTP). What is the correct statement for this feature?

A. MSTP configuration ID revision by default as switch serial number

B. MSTP configuration ID revision by default as current MSTP root priority

C. MSTP configuration ID name by default using switch serial number

D. MSTP configuration ID name by default using switch IMC address

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Download Free HP HPE6-A85 Demo

Simply submit your e-mail address below to get started with our free demo of your HP HPE6-A85 exam.