Juniper JN0-363 Actual Free Exam Questions & Community Discussion

Exam Code/Number: JN0-363
Exam Name/Title: Service Provider Routing and Switching, Specialist (JNCIS-SP)
Certification Provider: Juniper
Corresponding Certification: JNCIS-SP

Exam Questions: 88
Updated On: May 31, 2026

Question #19

What Is a key differentiator of generate routes from aggregate routes?

A. Generate routes use a forwarding next hop.

B. Generate routes have a default next-hop value of reject.

C. Generate routes have a default preference value of 210.

D. Generate routes cannot be used as a gateway of last resort.

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #20

You are implementing traffic engineering in your MPLS network. You must ensure that the MPLS routes are used to traverse your network. Your solution should not affect IGP routes in your route tables.
In this scenario, which traffic engineering setting will accomplish this behavior?

A. bgp-igp

B. bgp-igp-both-ribs

C. bgp

D. mpls-forwarding

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #21

Which two statements are correct about IS-IS? (Choose two.)

A. A level 1 only router can form an adjacency with a level 2 only router.

B. For level 2 adjacencies, the area IDs can be different.

C. For level 2 adjacencies, the area IDs must be the same.

D. A level 1 only router can never form an adjacency with a level 2 only router.

Discussion 0

Correct Answer: B,D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #22

Exhibit

You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses.
Which two tasks will accomplish your objective? (Choose two.)

A. Under the [edit routing-options] hierarchy, configure a 32-bit router ID.

B. Under the [edit routing-options] hierarchy, configure a 128-bit router ID.

C. issue the set protocols ospf3 area 0.0.0.0 interface ge-0/0/1.0 command.

D. Issue the sec protocols ospf area 0.0.0.0 interface ge-0/0/1.0 command.

Discussion 0

Correct Answer: A,C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #23

Exhibit

Which two statements are correct about the information shown in the exhibit? (Choose two.)

A. This switch has a bridge priority of 8k.

B. This switch is the root bridge for this spanning tree topology.

C. The root bridge is reachable using the ge-0/0/14 interface.

D. The root bridge's priority Is 4k.

Discussion 0

Correct Answer: A,C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #24

Which two statements are correct about segment routing? (Choose two.)

A. There are no segment routing adjacencies to maintain.

B. Segment routing adjacencies require very little resources to maintain.

C. Label assignments can be advertised through LDP updates.

D. Label assignments can be advertised through OSPF updates.

Discussion 0

Correct Answer: B,D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #25

Which new field is added to an IPv6 header as compared to IPv4?

A. version

B. fragment offset

C. checksum

D. flow label

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #26

Exhibit

You configured interface ge-0/070.0 to run IS-IS. but this interface does not appear in the output of the show isis adjacency command as shown in the exhibit.
What is the problem in this scenario?

A. The router at the other end of the link is a Level 1 only router.

B. This is a Gigabit Ethernet interface, that is incompatible with the reference-bandwidth 100g statement.

C. The router at the other end of the link Is not sending any IS-IS Hello messages.

D. The family iso statement must be added to the logical interface.

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #27

You are troubleshooting two OSPF routers that have an adjacency that remains in the ExStart state.
What would cause this problem?

A. mismatched OSPF hello intervals on the OSPF interfaces

B. mismatched MTU settings on the OSPF interfaces

C. mismatched subnet settings on the OSPF interfaces

D. mismatched authentication settings on the OSPF interfaces

Discussion 0

Correct Answer: B Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Download Free Juniper JN0-363 Demo

Simply submit your e-mail address below to get started with our free demo of your Juniper JN0-363 exam.