Juniper JN0-650 Actual Free Exam Questions & Community Discussion

Exam Code/Number: JN0-650
Exam Name/Title: Enterprise Routing and Switching, Professional (JNCIP-ENT)
Certification Provider: Juniper
Corresponding Certification: JNCIS-ENT

Exam Questions: 74
Updated On: Jun 02, 2026

Question #33

Exhibit

Referring to the exhibit, which two statements are correct? (Choose two.)

A. During times of no network congestion, traffic that is placed in queue 2 will be dropped if more than
10% of the interface bandwidth is used

B. The bandwidth reservation for queue 0 is 100%.

C. During times of sustained network congestion, traffic that is placed in queue 2 will be dropped if more than 10% of the interface bandwidth is used

D. The bandwidth reservation for queue 0 is 76%.

Discussion 0

Correct Answer: A,D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #34

According to IETF standards, which two statements are correct about EVPN/VXLAN deployments? (Choose two.)

A. Up to 16 million EVPN broadcast domains can exist.

B. IP packets within the same broadcast domain are forwarded unchanged.

C. Layer 2 frames within the same broadcast domain are forwarded unchanged.

D. Up to 16 million VXLAN broadcast domains can exist.

Discussion 0

Correct Answer: C,D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #35

You have configured DSCP CoS in your network and have applied BA and multifield classifiers to all interfaces.
In this scenario, which statement is correct?

A. If traffic matches both classifiers, then the BA classifier determines into which forwarding class the traffic is assigned.

B. You must set the multifield classifier to take precedence over the BA classifier or the configuration is ignored.

C. If traffic matches both classifiers, then the multifield classifier determines into which forwarding class the traffic is assigned

D. You must set the BA classifier to take precedence over the multifield classifier or the configuration is ignored

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #36

Exhibit

You are asked to configure VLAN load balancing on your network using MSTP. Referring to the exhibit, which two statements are correct? (Choose two.)

A. Switch1 will be the root bridge for msti 1.

B. Switch1 will assume the role of root bridge for both mstil and msti2 if Switch2 goes down.

C. Switch 1 will not assume the role of root bridge for both mstil and msti2 if Switch2 goes down.

D. Switch1 will be the root bridge for msti 2.

Discussion 0

Correct Answer: B,D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #37

Exhibit.

Referring to the exhibit, which two statements are correct? (Choose two.)

A. R5 will advertise the 203 0.113.0/24 route as an OSPF Type 7 LSA into Area 1.

B. R5 will advertise the 203 0.113 0/24 route as an OSPF Type 5 LSA into Area 1.

C. R1 will advertise the 203 0.113.0/24 route as an OSPF Type 5 LSA into Area 0

D. R1 will advertise the 203 0.113.0724 route as an OSPF Type 7 LSA into Area 0.

Discussion 0

Correct Answer: A,C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #38

Your OSPF network consists of a mix of 1GbE and 10GbE interfaces. By default, all interfaces have the same cost in your OSPF network. You are asked to ensure that the 10GbE interfaces are more preferred when available In this scenario, which two statements would accomplish this behavior? (Choose two.)

A. You should manually assign the interface metric for each 10GbE interface to be higher than the 1GbE interfaces in your OSPF network.

B. You should define the reference bandwidth as 1G. which will assign the 1GbE interfaces a higher cost.

C. You should define the reference bandwidth as 10G. which will assign the 1GbE interfaces a higher cost

D. You should manually assign the interface metric for each 1GbE interface to be higher than the 10GbE interfaces in your OSPF network.

Discussion 0

Correct Answer: C,D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #39

Your existing enterprise network uses OSPFv3 on Juniper devices. You need to extend the networking into a new building, and it needs to be in its own OSPF area. Your team is debating about making the area a stub Which two statements are correct in this scenario? (Choose two.)

A. Stub areas can be converted into totally stubby areas.

B. Stub areas can have an ASBR

C. Stub areas do not support virtual links.

D. Stub areas can also be not-so-stubby areas.

Discussion 0

Correct Answer: A,C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #40

When configuring OSPF. what is the purpose of adding the secondary command to an OSPF interface?

A. The secondary command sets a backup path for virtual links

B. The secondary command is used in conjunction with VRRP for failover.

C. The secondary command creates an mtra-area backup path.

D. The secondary command allows an interface to be in multiple areas.

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Download Free Juniper JN0-650 Demo

Simply submit your e-mail address below to get started with our free demo of your Juniper JN0-650 exam.