Oracle 1z1-404 Actual Free Exam Questions & Community Discussion

Exam Code/Number: 1z1-404
Exam Name/Title: Oracle Communications Session Border Controller 7 Basic Implementation Essentials
Certification Provider: Oracle
Corresponding Certification: Session Border Control

Exam Questions: 70
Updated On: Jul 12, 2026

Question #15

You are configuring access rules in a Session Border Controller Peering architecture.
Which two configuration steps are required to allow access only from User Agents (UAs) in a specific IP subnet? (Choose two.)

A. Navigate to the session-agent configuration element and set the ip-address parameter to the IP address of your trusted User Agent (UA).

B. Navigate to the sip-port configuration element and set the allow-anonymous parameter to realm-prefix.

C. Navigate to the sip-port configuration element and set the allow-anonymous parameter to agents-only.

D. Navigate to the sip-port configuration element and set the allow-anonymous parameter to all.

E. Navigate to therealm-config configuration element and set the addr-prefix parameter to the IP subnet of your trusted User Agents (UAs).

Discussion 0

Correct Answer: A,C Vote an answer

Question #16

A steering pool defines _____________.

A. an IP address and port the Session Border Controller uses for steering media to the external media server

B. arange of IP addresses used to route media flows as they egress the Session Border
Controller

C. an IP address and range of ports the Session Border Controller will use to declare itself as the destination for media flows in a session

D. a range of ports used to route media flows as they egress the Session Border Controller

E. a range of IP addresses and a pool of ports the Session Border Controller will use to declare itself as the destination for all subsequent media flows in a dialog

Discussion 0

Correct Answer: C Vote an answer

Question #17

When provisioning the redundancy-configuration, the peer name for each of the peers in a
High Availability configuration must also be defined in each system's ______________.

A. hostname parameter under the system-config configuration element

B. target name parameter under the bootparam configuration branch

C. hostname parameter under the bootparam configuration branch

D. hostname parameter under the sip-configconfiguration element

E. hostname parameter under the account-config configuration element

Discussion 0

Correct Answer: A Vote an answer

Question #18

Which two states are needed by the active node while transitioning to standby? (Choose two.)

A. Relinquishing-standby

B. Out of service

C. Becoming-standby

D. Becoming-active

E. Relinquishing-active

Discussion 0

Correct Answer: D,E Vote an answer

Question #19

What mechanism isused to ensure adjacent devices can redirect their Ethernet traffic to the
Session Border Controller that takes over, when a Session Border Controllers fails over?

A. HSRP

B. Gratuitous ARP

C. Proxy ARP

D. Reverse ARP

E. BOOTP

Discussion 0

Correct Answer: D Vote an answer

Question #20

In which two ways can you remove support for telnet from a media interface? (Choose two.)

A. Navigate to the network-interface configuration element and run the remove-telnet-ip
< IP address> command.

B. Navigate to the phy-interface configuration element and run the remove-hip-ip <IP address> command.

C. Navigate to the network-interface configuration element and run the remove-hip-ip <IP address> command.

D. Navigate to the network-interface configuration element and run the delete-hip-ip <IP address> command.

E. Navigate to the phy-interface configurationelement and run the remove-telnet-ip <IP address> command.

Discussion 0

Correct Answer: A,D Vote an answer

Question #21

The Session Border Controller ACLI is structured in a way that separates configuration of layers 3,4, and 5. This allows the system administrator to link each configuration together as needed for signaling and media routing purposes.
Which two options are valid to link signaling and media interfaces to a realm? (Choose two.)

A. Navigate to the iwf-config configuration element and set the media-interface-id parameter to the realm name.

B. Navigate to the sip-interface configuration element and set the realm-id parameter to the realm name.

C. Navigate to the network-interface configuration element and set the sip-interface-id parameter to the realm name.

D. Navigate to the steering-pool configuration element and set the realm-id parameter to the realm name.

E. Navigate to the account-config configuration element and set the realm-id parameter to the realm name.

Discussion 0

Correct Answer: A,E Vote an answer

Download Free Oracle 1z1-404 Demo

Simply submit your e-mail address below to get started with our free demo of your Oracle 1z1-404 exam.