Avaya 6101.1 Actual Free Exam Questions & Community Discussion

Exam Code/Number: 6101.1
Exam Name/Title: Avaya Ethernet Routing Switch Implementation Exam
Certification Provider: Avaya
Corresponding Certification: Avaya Specialist

Exam Questions: 70
Updated On: Aug 12, 2026

Question #8

In Ethernet Routing Switch (ERS) 5600 switch was added into the existing ERS 5500 stack, but ft did not form a proper stack.
Which statement describes the problem?

A. The stack was reset for a change in Base Unit to take effect.

B. The mode parameter on the ERS 5600 switch was set to Mixed Mode.

C. The ERS 5600 was set as the Base Unit.

D. The ERS 5500 was set as the Base Unit.

Discussion 0

Correct Answer: D Vote an answer

Question #9

A technician has complied me configuration of an Ethernet Routing (ERS) 5520 to and now must transfer a backup copy of configuration file to server.
Which command is used to accomplish this task?

A. 5520-24T-PWR# copy config ftp filename ers5520config.cfg

B. 5520.24T-PWR> copy config ftp filename ers5520 config.cfg

C. 5570-74T PWR# copy config tftp filename ers5520COnfig.cfg

D. 5520-24T-PWR# copy config scp filename ersS520conftg.cfg

Discussion 0

Correct Answer: C Vote an answer

Question #10

A technician is configuring a Link Aggregation connection from a stack of Ethernet Routing Switch (ERS) 5500 lo a core pair of ERS 8600 switches.
Which statement about the correct uplink configuration is true?

A. Disable auto negotiation and replace it with VLACP to identify single fiber fault failure

B. Enable Spanning Tree Protocol for the MLT when using it with SMLT in the core of the network.

C. Use unique MLT IDS for each stack of edge ERS 5500 switches

D. Distribute uplinks across different ERS 5500 switches in the stack.

Discussion 0

Correct Answer: D Vote an answer

Question #11

Which two pairs of commands will configure spanning tree on the edge switch? (Choose two)

A. 5520-24T (config) # interface fastethernet 1-20 5520-24T (config-if) # spanning tree learning disable

B. 5520-24T (config) # interface fastethernet 25-26 5520-24T (config-if) # spanning tree learning disable

C. 5520-24T (config) # interface fastethernet 25-26 5520-24T (corrfig-if) # spanning-tree learning fast

D. 5520-24T (config) # interface fastethernet 1-20 5520-24T (config-if) # spanning-tree learning fast

Discussion 0

Correct Answer: A,C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #12

A customer needs to install a new Ethernet Routing Switch (ERS) 2550T on the 172.16.5.0/24 network, but does not have a console cable available.
Which statement is correct?

A. The customer can connect to the network management Ethernet port which is pre-configured to use the 192 168 1 1/24 IP address

B. To communicate with an ERS 2550T the IP address must first be set though the console interface.

C. The customer can set the switch to use the temporary address of 192.168.192.168 by pressing the User Interface button on the front of the ERS 2550T

D. The switch will first attempt to use BootP to acquire an IP address, and if that fails it will assign IP address 192.160.1.1/24 to the switch IP.

Discussion 0

Correct Answer: A Vote an answer

Question #13

After issuing a show mlt list stats (CLI) or show ist Stat (ACLI) command, it is determined that the running type is normal MLT and not 1ST
What are two causes of the IST not running properly? (Choose two)

A. The peer IP addresses have to be 192.168.1.1/30 and 192.168.1.2/30.

B. The IST is not enabled on both switches.

C. The MLT ID does not match on both switches.

D. The peer IP address is not the address of the peer switch IST VLAN.

Discussion 0

Correct Answer: C,D Vote an answer

Question #14

A switch with Simple Loop Prevention Protocol (SLPP) did not detect a loop.
What are two reasons this occurred? (Choose two)

A. SLPP was not globally enabled

B. A premier License for SLPP is needed.

C. the VLAN where the loop originated to the SLPP transmitting list was not added.

D. Extended CP limit on the transmitting port was not configured.

Discussion 0

Correct Answer: A,C Vote an answer

Download Free Avaya 6101.1 Demo

Simply submit your e-mail address below to get started with our free demo of your Avaya 6101.1 exam.