Cisco 350-029 Actual Free Exam Questions & Community Discussion

Exam Code/Number: 350-029
Exam Name/Title: CCIE SP Written Exam, V3.0
Certification Provider: Cisco
Corresponding Certification: CCIE

Exam Questions: 520
Updated On: Aug 06, 2026

Question #1

Which statements about the Route Target Rewrite feature are not true? (Choose two.)

A. Route target replacement can be done on incoming and outgoing BGP updates.

B. Route target rewrites are supported for VRF export maps.

C. Route Target Rewrite allows the administration of the routing policy to stay local to the AS.

D. Route target replacement is always done by the ASBR.

E. After the route target replacement policy is applied to the target router, the BGP session need not be refreshed manually to put the policy into operation.

Discussion 0

Correct Answer: D,E Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #2

Refer to the exhibit.

An engineer is looking the CE1 routing table for CE2 Loopback 0. Each CE runs OSPF with its PE.
Which statement describes why the CE2 Loopback address is installed as an external OSPF route at the CE1 routing table?

A. PE1 and PE2 have different OSPF VRF processes.

B. CE1 and CE2 have different OSPF processes.

C. CE1 and CE2 are in different areas.

D. CE1 is configured under OSPF with the command redistribute connected.

E. PE1 and PE2 have mutual redistribution between OSPF and BGP.

Discussion 0

Correct Answer: A Vote an answer

Question #3

Which four of these are MPLS label header fields? (Choose four.)

A. FCS

B. Label

C. TTL

D. VPI VCI

E. EXP

F. S flag

Discussion 0

Correct Answer: B,C,E,F Vote an answer

Question #4

When you design QoS on CE for an MPLS Layer 2 VPN, which three things should be considered? (Choose three.)

A. Layer 3 link access QoS design

B. Layer 2 link access load balancing

C. Layer 2 access link QoS design

D. service provider service level agreements

E. enterprise-to-service-provider mapping models

Discussion 0

Correct Answer: C,D,E Vote an answer

Question #5

Which router or router combination is used to calculate the MPLS traffic engineering tunnel path?

A. middle-point router

B. head-end router

C. head-end router and tail-end router

D. tail-end router

Discussion 0

Correct Answer: B Vote an answer

Question #6

Refer to the exhibit.

A client is unable to receive traffic from multicast streamer (R5) on 234.1.1.1, even though multicast routing is established in the network.
Which statement describes how to resolve this issue?

A. R4 must be the DR on the R4-R6 segment.

B. The RP must be reachable via Fa0/0.

C. IGMP must be enabled for the client.

D. RP announcements have no multicast routing table entry.

E. A static mroute must be configured to point to RP via Fa0/1 on R4.

Discussion 0

Correct Answer: B Vote an answer

Question #7

Which three statements about 6VPE are true? (Choose three.)

A. MP-BGP can be used to propagate routes between the PE and the CE.

B. An additional address family was added to MP-BGP to support 6VPE.

C. 6VPE is functionally equivalent to VPNv4.

D. 6VPE routes are installed in the global routing table.

Discussion 0

Correct Answer: A,B,C Vote an answer

Question #8

DRAG DROP
Drag the ISIS packet types to correct type definition.

Discussion 0

Correct Answer:

Question #9

Refer to the exhibit.

Why is R4 unable to install any ISIS routes in the routing table?

A. Circuit levels are different.

B. ISIS LSP has an authentication issue.

C. No DR has been elected on this segment.

D. The metric style is mismatched.

Discussion 0

Correct Answer: D Vote an answer

Question #10

R3 and R4 are Route-Reflectors and there is an iBGP session between them, there is NO iBGP session between R1 and R2. For an External Route from CE-2 in R2 to reach R1, which two statements are true?

A. R1 acts as a Route-Reflector client to R4, R4 acts as a Route-Reflector client to R3, R2 acts as a Route-Reflector client to R3.

B. CE-2 establishes multi-hop E-BGP sessions with R3 and R4.

C. R1 acts as a Route-Reflector client to R3, R2 acts as a Route-Reflector client to R4.

D. R1, R3 and R4 establish full mesh iBGP sessions, R2, R3 and R4 establish full mesh iBGP sessions.

Discussion 0

Correct Answer: A,C Vote an answer

Question #11

Which MQC-based output queueing method is designed to support multiple traffic classes including VoIP traffic, mission-critical traffic, bulk traffic, interactive traffic and default class traffic?

A. CBWFQ

B. CB-WRED

C. Custom Queueing

D. WRR Queueing

E. LLQ

Discussion 0

Correct Answer: E Vote an answer

Download Free Cisco 350-029 Demo

Simply submit your e-mail address below to get started with our free demo of your Cisco 350-029 exam.