Fortinet NSE7 Actual Free Exam Questions & Community Discussion

Exam Code/Number: NSE7
Exam Name/Title: NSE7 Enterprise Firewall - FortiOS 5.4
Certification Provider: Fortinet
Corresponding Certification: Troubleshooting Professional

Exam Questions: 87
Updated On: Oct 02, 2026

Question #1

The CLI command set intelligent-mode <enable | disable> controls the IPS engine's adaptive scanning behavior. Which of the following statements describes IPS adaptive scanning?

A. Determines the optimal number of IPS engines required based on system load.

B. Determines when it is secure enough to stop scanning session traffic.

C. Choose a matching algorithm based on available memory and the type of inspection being performed.

D. Downloads signatures on demand from FDS based on scanning requirements.

Discussion 0

Correct Answer: C Vote an answer

Question #2

Examine the output of the 'get router info ospf interface' command shown in the exhibit; then answer the question below.

Which statements are true regarding the above output? (Choose two.)

A. The port4 interface is connected to the OSPF backbone area.

B. The local FortiGate has been elected as the OSPF backup designated router.

C. There are at least 5 OSPF routers connected to the port4 network.

D. Two OSPF routers are down in the port4 network.

Discussion 0

Correct Answer: A,D Vote an answer

Question #3

View the exhibit, which contains a screenshot of some phase-1 settings, and then answer the question below.

The VPN is up, and DPD packets are being exchanged between both IPsec gateways; however, traffic cannot pass through the tunnel. To diagnose, the administrator enters these CLI commands:

However, the IKE real time debug does not show any output. Why?

A. The log-filter setting was set incorrectly. The VPN's traffic does not match this filter.

B. The debug output shows phases 1 and 2 negotiations only. Once the tunnel is up, it does not show any more output.

C. The debug output shows phase 1 negotiation only. After that, the administrator must enable the following real time debug: diagnose debug application ipsec -1.

D. The debug shows only error messages. If there is no output, then the tunnel is operating normally.

Discussion 0

Correct Answer: C Vote an answer

Question #4

Which of the following statements is true regarding a FortiGate configured as an explicit web proxy?

A. FortiGate limits the total number of simultaneous explicit web proxy users.

B. FortiGate limits the number of simultaneous sessions per explicit web proxy user. This limit CANNOT be modified by the administrator.

C. FortiGate limits the number of workstations that authenticate using the same web proxy user credentials.
This limit CANNOT be modified by the administrator.

D. FortiGate limits the number of simultaneous sessions per explicit web proxy user The limit CAN be modified by the administrator

Discussion 0

Correct Answer: D Vote an answer

Question #5

View the exhibit, which contains the output of diagnose sys session list, and then answer the question below.

If the HA ID for the primary unit is zero (0), which statement is correct regarding the output?

A. This session is synced with the slave unit.

B. This session cannot be synced with the slave unit.

C. The inspection of this session has been offloaded to the slave unit.

D. This session is for HA heartbeat traffic.

Discussion 0

Correct Answer: A Vote an answer

Question #6

An administrator cannot connect to the GIU of a FortiGate unit with the IP address 10.0.1.254. The administrator runs the debug flow while attempting the connection using HTTP. The output of the debug flow is shown in the exhibit:

Based on the error displayed by the debug flow, which are valid reasons for this problem? (Choose two.)

A. HTTP administrative access is disabled in the FortiGate interface with the IP address 10.0.1.254.

B. The packet is denied because of reverse path forwarding check.

C. HTTP administrative access is configured with a port number different than 80.

D. Redirection of HTTP to HTTPS administrative access is disabled.

Discussion 0

Correct Answer: A,C Vote an answer

Question #7

Examine the output of the 'diagnose debug rating' command shown in the exhibit; then answer the question below.

Which statement are true regarding the output in the exhibit? (Choose two.)

A. FortiGate will send the FortiGuard queries to the server with highest weight.

B. A server's round trip delay (RTT) is not used to calculate its weight.

C. There are three FortiGuard servers that are not responding to the queries sent by the FortiGate.

D. The TZ value represents the delta between each FortiGuard server's time zone and the FortiGate's time zone.

Discussion 0

Correct Answer: A,D Vote an answer

Question #8

When does a RADIUS server send an Access-Challenge packet?

A. The server does not have the user credentials yet.

B. The user account is not found in the server.

C. The user credentials are wrong.

D. The server requires more information from the user, such as the token code for two-factor authentication.

Discussion 0

Correct Answer: D Vote an answer

Question #9

Which real time debug should an administrator enable to troubleshoot RADIUS authentication problems?

A. Diagnose debug application radius -1.

B. Diagnose radius console -log enable.

C. Diagnose debug application fnbamd -1.

D. Diagnose authd console -log enable.

Discussion 0

Correct Answer: A Vote an answer

Download Free Fortinet NSE7 Demo

Simply submit your e-mail address below to get started with our free demo of your Fortinet NSE7 exam.