Juniper JN0-352 Actual Free Exam Questions & Community Discussion

Exam Code/Number: JN0-352
Exam Name/Title: Enterprise Routing and Switching, Specialist (JNCIS-ENT)
Certification Provider: Juniper
Corresponding Certification: JNCIS-ENT

Exam Questions: 149
Updated On: Jun 24, 2026

Question #1

Which two statements about redundant trunk groups on EX Series switches are correct? (Choose two.)

A. Redundant trunk groups must be connected to the same aggregation switch.

B. Redundant trunk groups load-balance traffic across two designated uplink interfaces.

C. Layer 2 control traffic is permitted on the secondary link

D. If the active link fails, then the secondary link automatically takes over.

Discussion 0

Correct Answer: C,D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #2

Which two statements are correct about tunnels? (Choose two.)

A. Tunnels add additional overhead to packet size.

B. Tunnel endpoints must have a valid route to the remote tunnel endpoint.

C. IP-IP tunnels are stateful.

D. BFD cannot be used to monitor tunnels.

Discussion 0

Correct Answer: A,B Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #3

You want to redistribute the static routes into BGP, but they do not show as BGP routes.
What causes this result to occur?

A. A community string must be configured.

B. The static routes do not have a valid next hop.

C. The no-readvertisefeature is specified.

D. The as-pathparameter must be specified.

Discussion 0

Correct Answer: B Vote an answer

Question #4

You are deploying a trunk port with multiple VLANs. In this scenario, which statement is true about the native VLAN?

A. The native VLAN must be the default VLAN on the port.

B. The native VLAN is the highest tagged VLAN ID on the port.

C. The native VLAN is an untagged VLAN ID on the port.

D. The native VLAN is automatically configured through DHCP.

Discussion 0

Correct Answer: C Vote an answer

Question #5

Which statement about aggregate routes is correct?

A. Aggregate routes are always preferred over more specific routes, even when the specific routes have a better path.

B. Aggregate routes are automatically generated for all of the subnets in a routing table.

C. Aggregate routes are used for advertising summarized network prefixes.

D. Aggregate routes can only be used for static routing but not for dynamic routing protocols.

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #6

Which two statements about MACsec are true? (Choose two.)

A. MACsec is an IEEE standard.

B. MACsec does not provide data integrity.

C. MACsec functions on point-to-point connections.

D. MACsec functions on point-to-multipoint connections.

Discussion 0

Correct Answer: A,C Vote an answer

Question #7

What is the default hello interval on an OSPF interface?

A. 10 seconds

B. 30 seconds

C. 60 seconds

D. 20 seconds

Discussion 0

Correct Answer: A Vote an answer

Question #8

You are troubleshooting a BGP routing issue between your network and a customer router and are reviewing the BGP routing policies. Which two statements are correct in this scenario?
(Choose two.)

A. Import policies are applied after the RIB-ln table.

B. Export policies are applied to routes in the RIB-ln table.

C. Import policies are applied to routes in the RIB-Local table.

D. Export policies are applied after the RIB-Local table.

Discussion 0

Correct Answer: A,D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #9

You are configuring an IS-IS IGP network and do not see the IS-IS adjacencies established. In this scenario, what are two reasons for this problem? (Choose two.)

A. IP subnets are not a /30 address.

B. MTU is not at least 1492 bytes.

C. The lo0 interface is not included as an IS-IS interface.

D. The Level 2 routers have mismatched areas.

Discussion 0

Correct Answer: B,C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Download Free Juniper JN0-352 Demo

Simply submit your e-mail address below to get started with our free demo of your Juniper JN0-352 exam.