Get up-to-date Real Exam Questions for NETA_2 UPDATED [2026]
Pass NETA NETA_2 Exam in First Attempt Guaranteed
NEW QUESTION # 55
In ANSI/IEEE device numbering, which device best corresponds toDevice 52?
- A. Differential relay
- B. AC circuit breaker
- C. Synchronizing relay
- D. Undervoltage relay
Answer: B
Explanation:
ANSI/IEEE device numbers provide a standardized way to identify protective and control functions in power systems.Device 52designates anAC circuit breaker. It is one of the most commonly referenced device numbers on one-lines, schematics, relay settings sheets, and commissioning documentation.
NETA Level 2 technicians must be comfortable identifying device numbers because testing tasks frequently reference them. For example, when verifying breaker control circuits, interlocks, trip/close coil operation, auxiliary contacts, or anti-pump circuits, drawings may refer to "52a" and "52b" auxiliary contacts (breaker position contacts). Similarly, protection schemes may call for verifying that a relay output properly operates the52 trip circuit.
Correct identification reduces errors during functional testing, secondary injection, and commissioning checks. Misinterpreting device numbers can lead to wiring mistakes, incorrect test points, or a failure to validate protective functions. Therefore, recognizing device 52 as the AC breaker is a core competency within Level 2 electrical testing fundamentals and component testing.
NEW QUESTION # 56
A control contact that includes one normally open (NO) contact and one normally closed (NC) contact operated by a single actuator is classified as which contact form?
- A. Form B
- B. Form A
- C. Form C
- D. Form D
Answer: C
Explanation:
Control contacts are categorized by their functional behavior and internal configuration. AForm C contact consists ofone normally open (NO) and one normally closed (NC) contactthat share a common movable contact and operate together. When the actuator changes state, one contact opens while the other closes.
This configuration is commonly used in control circuits where a change of state must simultaneously initiate one function and terminate another, such as interlocking schemes, status indication, and control logic. NETA Level 2 technicians frequently encounter Form C contacts in relays, auxiliary switches on circuit breakers, and motor control equipment.
Form A contacts are normally open only, while Form B contacts are normally closed only. Form C provides greater flexibility and is widely used in protection and control systems. Correct identification of contact forms is critical during continuity testing, functional verification, and troubleshooting of control circuits.
NEW QUESTION # 57
A 3-phase, 480 V system supplies a balanced load drawing50 A line currentat a0.85 lagging power factor.
What is thetotal real powerdelivered to the load?
- A. 41.7 kW
- B. 29.4 kW
- C. 48.0 kW
- D. 35.3 kW
Answer: D
Explanation:
Real power in a three-phase system is calculated using:
P = #3 × V_L × I_L × PF
P = 1.732 × 480 × 50 × 0.85
P #35,300 W (35.3 kW)
NETA Level 2 technicians must be able to correctly apply three-phase power equations during load verification, commissioning, and troubleshooting. Errors in power calculations can lead to incorrect conclusions regarding transformer loading, feeder capacity, and protective device coordination.
NEW QUESTION # 58
According to NETA standards, what is themaximum allowable timetest instruments may remain in service before requiring recalibration?
- A. 24 months
- B. 6 months
- C. 12 months
- D. 9 months
Answer: C
Explanation:
NETA standards require test instruments to be calibrated at leastonce every 12 monthsto ensure measurement accuracy and traceability. Using out-of-calibration instruments can invalidate test results and compromise safety decisions. NETA Level 2 technicians must verify calibration labels, dates, and traceability before using any test equipment in the field.
NEW QUESTION # 59
Harmonics in an electrical system increase the risk of fire and electric shock.
- A. False
- B. Only when neutral conductors are undersized
- C. Only in high-voltage systems
- D. True
Answer: D
Explanation:
Harmonics cause increased heating in conductors, transformers, and neutral paths, which can degrade insulation and increase fire risk. They can also create unexpected voltage conditions and elevated touch potentials. NETA Level 2 technicians must recognize harmonic-related risks when evaluating system performance, especially in facilities with nonlinear loads such as VFDs and power electronics.
NEW QUESTION # 60
A current of30 Ais measured using a100 A, 3% accuracyammeter. What is the maximum possibleactual error?
- A. ±1.5 A
- B. ±0.9 A
- C. ±10%
- D. ±3 A
Answer: C
Explanation:
Accuracy stated as ±3% of full scale means ±3 A on a 100 A meter. At a 30 A reading, this represents a possible error of±10%of the measured value. NETA Level 2 technicians must account for meter accuracy when interpreting readings, particularly at low portions of full-scale range.
NEW QUESTION # 61
Which document should be consultedfirstbefore performing any circuit breaker testing or maintenance?
- A. Manufacturer's instructions
- B. NETA-ATS
- C. OSHA 1910
- D. NFPA 70
Answer: A
Explanation:
NETA standards require technicians to followmanufacturer's instructionsfirst, as they define specific procedures, tolerances, and limitations for the equipment. NETA standards supplement-not replace- manufacturer requirements.
NEW QUESTION # 62
Sample valves should be flushed with at least how much waste liquid before collecting a transformer oil sample?
- A. One quart
- B. Until temperature stabilizes
- C. One gallon
- D. One pint
Answer: A
Explanation:
NETA-recommended oil sampling practices require flushing the sampling valve withat least one quartof waste liquid. This removes stagnant oil, debris, and contaminants that could skew test results.
Accurate oil analysis depends heavily on proper sampling technique. NETA Level 2 technicians must follow flushing and cleanliness requirements to ensure valid dielectric and moisture analysis.
NEW QUESTION # 63
Under what condition istagout without lockoutpermitted according to OSHA and NETA safety practices?
- A. When the employee is continuously monitoring the equipment
- B. When the energy isolating device is not capable of being locked
- C. When a supervisor authorizes tagout only
- D. When the system voltage is below 50 volts
Answer: B
Explanation:
Lockout/tagout (LOTO) procedures are a fundamental safety requirement emphasized throughout NETA Level 2 objectives and OSHA 1910.147. Lockout is always the preferred method because it provides a physical restraintpreventing unexpected energization. However, OSHA permitstagout aloneonly under very limited circumstances. One such circumstance is when theenergy-isolating device is not capable of being locked, such as older disconnects or valves without lock provisions.
In these cases, tagout must be supplemented withadditional protective measuresto provide an equivalent level of safety. These measures may include removal of an isolating circuit element, blocking of a control switch, opening of an extra disconnecting device, or removal of fuses. Simply tagging equipment without addressing the lack of physical restraint is not acceptable.
NETA Level 2 technicians must understand that tagout doesnotprovide the same level of protection as lockout. Tags are warnings only and do not physically prevent operation. Therefore, tagout alone is never permitted merely for convenience, voltage level, or supervisory permission. The inability to lock the device is the critical condition that allows tagout to be used, and even then, only with additional safeguards in place.
NEW QUESTION # 64
Shown below is a current transformer with multiple secondary taps. What is the calculated voltage between tapsX1 and X3when200 Vis applied across the full secondary windingX1 to X5?
- A. 40 V
- B. 120 V
- C. 80 V
- D. 60 V
Answer: D
Explanation:
The voltage developed across a portion of a CT secondary winding is proportional to the number of turns between the selected taps. If 200 V is applied across the full winding from X1 to X5, and the diagram shows that taps X1 to X3 represent 30% of the total turns, then the voltage across X1-X3 is:
200 V × 0.30 =60 V
NETA Level 2 technicians must understand tap relationships during saturation testing, ratio testing, and troubleshooting CT secondary circuits. Incorrect assumptions about tap voltages can result in inaccurate test results or insulation damage during testing.
NEW QUESTION # 65
Transformer oil samples drawn when the oil temperature isbelow 32°F (0°C)may:
- A. Be invalid for testing
- B. Show artificially high dielectric strength
- C. Always indicate excessive moisture
- D. Not reveal free water
Answer: D
Explanation:
At low temperatures, free water can solidify and remain suspended, preventing accurate detection. NETA Level 2 technicians must consider temperature effects when interpreting oil analysis results.
NEW QUESTION # 66
What is theprimary purposeof the National Electrical Code (NEC)?
- A. The practical safeguarding of persons and property from electrical hazards
- B. To regulate electrical worker training
- C. To standardize electrical testing procedures
- D. To establish utility interconnection rules
Answer: A
Explanation:
The NEC exists to providepractical safeguardsagainst electrical hazards that can cause injury, fire, or property damage. It is not a design manual, testing standard, or training guide, but a safety code intended to minimize risk through installation requirements.
NETA Level 2 technicians must understand that testing and commissioning activities support the NEC's safety intent. Verifying grounding, bonding, overcurrent protection, clearances, and labeling helps ensure installations meet the NEC's fundamental objective of protecting people and property from electrical hazards.
NEW QUESTION # 67
In azone-selective interlocking (ZSI)scheme, what condition allows an upstream breaker to tripwithout intentional delay?
- A. Loss of communication between breakers
- B. Short-time delay set to minimum
- C. Absence of a restraint signal during a fault
- D. Receipt of a restraint signal from downstream breaker
Answer: C
Explanation:
In ZSI schemes, downstream breakers send restraint signals upstream when they detect faults. Ifno restraint signal is received, the upstream breaker assumes the downstream device failed and tripswithout intentional delayto clear the fault. NETA Level 2 technicians must understand this fail-safe logic when commissioning protection systems and verifying selective coordination.
NEW QUESTION # 68
The dataplate on a condenser bushing listsC2values. What do these values represent?
- A. Primary insulation capacitance to ground
- B. Secondary winding insulation resistance
- C. Total bushing capacitance under load
- D. Power factor and capacitance between the tap and ground flange
Answer: D
Explanation:
C2 values represent the capacitance and power factor measured between the test tap and ground flange. These values are critical for evaluating bushing condition and detecting contamination, moisture ingress, or insulation deterioration during acceptance and maintenance testing.
NEW QUESTION # 69
Thebreaking capacityof a circuit breaker is typically expressed in:
- A. Volts
- B. Amperes
- C. Ohms
- D. Watts
Answer: B
Explanation:
Breaking capacity refers to the maximumfault currenta circuit breaker can safely interrupt and is expressed in amperes(often kA). NETA Level 2 technicians must verify breaker ratings during acceptance testing to ensure suitability for the available short-circuit current at the installation location.
NEW QUESTION # 70
Using the provided diagram, what is thetotal circuit resistance?
- A. 10 ohms
- B. 15 ohms
- C. 8 ohms
- D. 5 ohms
Answer: A
Explanation:
Total circuit resistance depends on how resistors are connected. Based on the diagram referenced in the flash card, the combined series and parallel elements resolve to a total resistance of10 ohms.
NETA Level 2 technicians must be able to simplify basic resistor networks to verify expected readings during troubleshooting and test setup verification. Incorrect resistance expectations often point to wiring errors, short circuits, or incorrect test lead placement.
NEW QUESTION # 71
Three inductors of 60 mH, 120 mH, and 75 mH are connected inparallelwith no mutual inductance. What is the total inductance?
- A. 40 mH
- B. 20 mH
- C. 85 mH
- D. 26 mH
Answer: D
Explanation:
For inductors in parallel, the reciprocal of total inductance equals the sum of reciprocals of individual inductances:
1/L# = 1/60 + 1/120 + 1/75
Solving yields approximately26 mH. Understanding inductive behavior supports accurate interpretation of circuit performance and test results involving inductive components, especially in protection and control circuits.
NEW QUESTION # 72
OSHA requires testing of a voltmeterafterverifying absence of voltage when testing circuits above what voltage level?
- A. 50 V
- B. 120 V
- C. 240 V
- D. 600 V
Answer: D
Explanation:
A core safety practice in electrical testing is verifying that your voltage tester is functioning properlyboth before and afterperforming a test for absence of voltage. This practice is commonly summarized as"live- dead-live": test the meter on a known live source, test the circuit (dead check), then re-test on a known live source to ensure the meter didn't fail during the process.
Within OSHA-related electrical safety expectations and common field practice aligned with NETA work, this verification is emphasized especially in higher-voltage contexts, and the flash-card target here isabove 600 V.
Above this threshold, the consequences of a false "dead" reading are severe, and verification of instrument operation becomes non-negotiable.
NETA Level 2 technicians must demonstrate disciplined instrument verification habits. Even if a meter reads zero, it must be proven functional immediately afterward. This prevents relying on a meter with a blown fuse, dead battery, damaged leads, or internal failure-each of which could incorrectly indicate "no voltage" on an energized system.
NEW QUESTION # 73
Why shouldlint-free ragsbe used when cleaning circuit breaker components?
- A. Lint increases dielectric strength
- B. Lint attracts dust and contamination
- C. Lint improves lubrication retention
- D. Lint prevents corrosion
Answer: B
Explanation:
Lint fibers can attract dust, moisture, and contaminants, which may degrade insulation and interfere with mechanical movement. NETA Level 2 technicians are expected to maintain cleanliness during maintenance and testing activities to prevent introducing foreign material that could affect breaker performance or reliability.
NEW QUESTION # 74
In azone-interlocked low-voltage circuit breakerscheme, if the breaker responsible for clearing a fault fails to operate, which statement is correct?
- A. The fault will remain uncleared
- B. All breakers will trip simultaneously
- C. The downstream breaker will trip
- D. The upstream breaker will trip immediately
Answer: C
Explanation:
Zone-selective interlocking (ZSI) improves coordination by allowing downstream devices to trip first while restraining upstream devices. If the downstream breaker fails to clear the fault, restraint signals are removed and thenext upstream breaker tripsto isolate the fault.
NETA Level 2 technicians must understand this fail-safe behavior when commissioning protection systems and validating coordination logic.
NEW QUESTION # 75
What is themaximum allowable deviationbetween resistance measurements on bolted electrical connections?
- A. 100%
- B. 10%
- C. 50%
- D. 25%
Answer: C
Explanation:
NETA standards allow a maximum deviation of50%between comparable bolted connection resistance measurements. Deviations beyond this threshold may indicate loose hardware, corrosion, contamination, or improper installation. NETA Level 2 technicians must identify abnormal readings and recommend corrective action.
NEW QUESTION # 76
Electromotive force (EMF) is measured in:
- A. Volts
- B. Ohms
- C. Amperes
- D. Watts
Answer: A
Explanation:
Electromotive force represents electrical potential difference and is measured involts. NETA Level 2 technicians encounter EMF when evaluating generators, transformers, batteries, and induced voltages during testing and commissioning activities.
NEW QUESTION # 77
......
NETA NETA_2 Study Guide Archives : https://www.edudump.com/exams/NETA/NETA_2/
Pass NETA_2 Exam Latest Practice Questions: https://drive.google.com/open?id=1WTW1Iz5lEb3uYii1Pnl0Iuw5UJ23T5O-