Latest EMC D-PE-OE-01 Actual Free Exam Questions & Community Discussion, Page 3

Question #29

Which two memory settings optimize a PowerEdge 16G server to support VMware ESXi?

A. Near Balanced Configuration and Optimizer Mode

B. Balanced Memory Configuration and Dell Fault Resilient Mode

C. Near Balanced Configuration and Dell Fault Resilient Mode

D. Balanced Memory Configuration and Optimizer Mode

Discussion 0

Correct Answer: D Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #30

A technician needs to improve overall server performance. All servers run a Dell-supported version of RedHat Linux. Turbo boost has been highly beneficial. CPU performance should be maximized, but not at the expense of power usage.
What is the most efficient way to implement these profile options?

A. In iDRAC, under Hardware > CPU, enable Turbo mode and Dell Active Power Control

B. In iDRAC, under Hardware Overview > System Performance, select Performance mode

C. In System BIOS Settings, select Performance per Watt (Dell Active Power Control)

D. In System BIOS Settings, select Performance per Watt (Operating System)

Discussion 0

Correct Answer: C Vote an answer

Question #31

You are installing a PowerEdge R7725 into a Bank Data Center. One of the requirements Is to ensure only trusted devices can be used to boot. What BIOS settings can be used to meet this requirement?

A. System Security > Set Secure Boot to Enable

B. Network Settings > Set all UEFI PXE Settings to Disabled

C. Boot Settings > BIOS Boot Settings > Boot Sequence

D. Boot Settings > Set Boot Mode to BIOS

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #32

A server is experiencing latency issues, and the end user was told to disable C States and C1E.
Where can these settings be checked in the BIOS?

A. System Information

B. Processor Settings

C. System Profile Settings

D. Miscellaneous Settings

Discussion 0

Correct Answer: C Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #33

A technician receives an email alert that one of the drives on a server has failed. Upon replacing the bad drive, they receive a second email alert that the same drive has failed. The technician installs the replacement drive in another server and it works correctly.
What is a valid troubleshooting step for this issue?

A. Replace the PERC

B. Recreate the RAID array

C. Check if the cables are properly seated to the backplane

D. Perform a full initialization on the replacement drive

Discussion 0

Correct Answer: C Vote an answer

Question #34

A technician is troubleshooting a server with the following components:
Two CPUs
Memory installed in sockets A1, A2, A3, A4, A5, A6, B1, B2, B3, B4, B5 and B6 Expansion cards installed in all expansion slots
6x 1 TB drives configured as a RAID 6 virtual disk
The server has the following symptoms:
CPU2 has failed
Memory in slots B1, B2, B3, B4, B5 and B6 is not accessible
Some of the expansion cards have gone offline.
What should the technician do to resolve this issue?

A. Replace CPU2

B. Reboot the server, access the Lifecycle and re-enable CPU2

C. Replace the system board

D. Replace the failing CPU, failing memory, and expansion cards

Discussion 0

Correct Answer: A Vote an answer

Question #35

What is the correct order of steps taken during the BIOS/UEFI Recovery process?

Discussion 0

Correct Answer:

Question #36

What is a requirement to operate GPUs in a Dell EMC PowerEdge R740 server?

A. All GPU cards must be installed at the same time

B. All GPU cards must be of the same type but can be a different model

C. All GPU cards must be installed on the same riser card

D. All GPU cards must be of the same type and model

Discussion 0

Correct Answer: D Vote an answer

Question #37

A server has six memory modules attached to each CPU Memory Optimizer mode is configured. The user now wants to have maximum protection for the memory but cannot afford to lose any memory space.
What should the technician install/configure?

A. No additional memory, Switch on Single Rank Spare Mode

B. Six additional memory modules matching the original, Switch on Single Rank Spare Mode

C. Six additional memory modules matching the original, Switch to Memory Mirroring

D. No additional memory, Switch to memory Mirroring

Discussion 0

Correct Answer: C Vote an answer

Question #38

A Dell PowerEdge R750 shows a sudden reduction in usable capacity on a RAID 6 virtual disk after replacing a failed drive with a larger one. The OS and iDRAC both report the VD as "Ready'" and "Optimal" but usable capacity remains unchanged. What is the cause of this behavior?

A. The virtual disk remains limited by the smallest disk

B. The drive was added as a dedicated hot spare instead of a member disk

C. The virtual disk automatically expanded but the OS has not refreshed

D. The rebuild failed and the virtual disk is using reduced capacity mode

Discussion 0

Correct Answer: A Vote an answer

Explanation: Only visible for EduDump members. You can sign-up / login (it's free).

Question #39

An engineer needs to upgrade a Dell EMC PowerEdge R440 server from a single PSU to dual PSU configuration. There are unused PSU modules from PowerEdge R430 and R420 servers available, and they have the same wattage ratings.
What should the engineer do to complete the task?

A. Add the PowerEdge R430 PSU modules to the PowerEdge R440

B. Configure the PowerEdge R440 PSU with 1+1 configuration

C. Order a new PSU specific to the existing PowerEdge R440

D. Add the PowerEdge R420 PSU modules to the PowerEdge R440

Discussion 0

Correct Answer: C Vote an answer

Question #40

Which two tools provide a user interface to manage the Boot Optimized Storage Solution (BOSS) cards?(Select 2)

A. Remote Access Controller Admin (RACADM)

B. OpenManage Server Administrator (OMSA)

C. Intelligent Platform Management Interface Tool (IPMITool)

D. Integrated Dell Remote Access Controller (iDRAC)

E. OpenManage Mobile (OMM)

Discussion 0

Correct Answer: B,D Vote an answer

Question #41

A technician needs to configure a server to PXE boot a server setup image with the BIOS in UEFI mode.
Which two steps should the technician perform to enable this function?(Choose two.)

A. From the iDRAC web interface, select Network Settings, and enable PXE Device1.

B. Boot to Ctrl+S and configure the NIC for PXE Device1.

C. From System Setup Utility, choose Device Settings. Configure NIC for PXE.

D. Navigate to Network Settings, PXE Device1 Settings, and configure IP.

E. Navigate to Boot Options Settings and set PXE Device1 as first option.

Discussion 0

Correct Answer: B,E Vote an answer

Question #42

A Dell PowerEdge R740 server with two CPUs has six memory modules that are attached to each CPU. Memory Optimizer mode is configured. The user now wants to have maximum protection for the memory but cannot afford to lose any memory space.
What should be installed or configured?

A. No additional memory, Switch on Single Rank Spare Mode

B. No additional memory, Switch to Memory Mirroring

C. Six additional memory modules matching the original, Switch on Single Rank Spare Mode

D. Twelve additional memory modules matching the original (six for each CPU), Switch to Memory Mirroring

Discussion 0

Correct Answer: D Vote an answer

EMC D-PE-OE-01 Actual Free Exam Questions & Community Discussion

Download Free EMC D-PE-OE-01 Demo