F5 201 Actual Free Exam Questions & Community Discussion
A BIG-IP Administrator wants to add the ASM Module to an HA pair of BIG-IP devices. The BIG-IP Administrator has already installed a new Add-On License on both devices in the HA pair. What should the BIG-IP Administrator do next to use the module?
Correct Answer: B
Vote an answer
The ICMP monitor has been assigned to all nodes. In addition, all pools have been assigned custom monitors. The pool is marked available. If a pool is marked available (green) which situation is sufficient to cause this?
Correct Answer: D
Vote an answer
The BIG-IP Administrator generates QKView using tmsh command "qkview -SO". In which directory does the BIG-IP appliance save the QKView?
Correct Answer: A
Vote an answer
Some users who connect to a busy Virtual Server have connections reset by the BIG-IP system. Pool member resources are NOT a factor in this behavior. What is a possible cause for this behavior?
Correct Answer: A
Vote an answer
Explanation: Only visible for EduDump members. You can sign-up / login (it's free).
Refer to the exhibit.
Which two pool members should be chosen for a new connection? (Choose two.)
Which two pool members should be chosen for a new connection? (Choose two.)
Correct Answer: C,D
Vote an answer
A BIG-IP Administrator uses a device group to share the workload and needs to perform service on a BIG-IP device currently active for a traffic group. The administrator needs to enable the traffic group to run on another BIG-IP device in the device group. What should the administrator do to meet the requirement?
Correct Answer: D
Vote an answer
A BIG-IP Administrator assigns the default http health monitor to a pool that has three members listening on port 80 When the administrator connects to each pool member via the CURL utility, two of the members respond with a status of 404 Not Found while the third responds with 200 OK. What will the pool show for member availability?
Correct Answer: D
Vote an answer
A BIG-IP system has the following configuration:
* SNAT is set to Auto Map
* There are two VLANs internal and external
* Default route is pointed to the gateway on external VLAN
* Self P for internal VLAN is 1921.1.2
* Self IP for external VLAN is 192.1.2.2
* Floating IP addresses for internal VLAN is 192.1.1.1
* Floating IP addresses for external VLAN is 192.1.2.1
* The Virtual Server IP address is 192.1.1.100
Which IP address does the BIG-IP system use first when traffic reaches the servers on the internal VLAN?
* SNAT is set to Auto Map
* There are two VLANs internal and external
* Default route is pointed to the gateway on external VLAN
* Self P for internal VLAN is 1921.1.2
* Self IP for external VLAN is 192.1.2.2
* Floating IP addresses for internal VLAN is 192.1.1.1
* Floating IP addresses for external VLAN is 192.1.2.1
* The Virtual Server IP address is 192.1.1.100
Which IP address does the BIG-IP system use first when traffic reaches the servers on the internal VLAN?
Correct Answer: B
Vote an answer
An IT support engineer needs to access and modify Virtual Servers in three partitions (Common /Banking and Dev) daily on a BIG-IP device. The company operates a Least Privilege access policy. What level of access does the IT support engineer need to ensure completion of daily roles?
Correct Answer: C
Vote an answer
The incoming client IP address is 205.12.45.52. The last five connections have been sent to members C, D, A, B, B. Given the virtual server and pool definitions and the statistics shown in the graphic, which member will be used for the next connection?
Correct Answer: D
Vote an answer
Refer to the exhibit
The BIG-IP Administrator is unable to access the management console via Self-IP 10.10 1.33 and port 443.
What is the reason for this problem?
The BIG-IP Administrator is unable to access the management console via Self-IP 10.10 1.33 and port 443.
What is the reason for this problem?
Correct Answer: A
Vote an answer
0
0
0
10